Volkswagen Amarok 2011- Hydraulic Power Steering Rack

VW Amarok 2011- RHD — Hydraulic Power Steering (HPS) Overview

The VW Amarok 2011- RHD (OE 2H2422055B) is a hydraulic power steering (hps) designed for Volkswagen Amarok (2H), Audi Q7 (4L) models produced from 2011-2022. This is a right-hand drive (RHD) variant designed for the UK, Australia, Japan, South Africa, and other RHD markets. This steering unit is manufactured to OE specifications and provides precise, responsive steering feel for 2.0L TDI CDCA/CNEA, 3.0L TDI CASA/CATA engine variants. At KITLAMT, we produce this hydraulic power steering (hps) with strict quality control, ensuring every unit meets or exceeds the original equipment standard.

Our hydraulic power steering (hps) for the VW Amarok 2011- RHD undergoes rigorous testing including pressure cycling (100,000+ cycles), salt spray resistance (500+ hours), and dimensional verification against the OE reference. Each unit is individually bench-tested for leaks, steering effort, and return-to-center performance before shipping. We supply this part to importers, distributors, and workshops across 50+ countries with factory direct pricing and fast lead times.

Compatible Vehicles — Volkswagen Amarok (2H) and Related Models

This hydraulic power steering (hps) is confirmed to fit the following vehicles:

• Amarok (2H) — 2011-2022 production
• Audi Q7 (4L) — 2011-2022 production

Engine compatibility: 2.0L TDI CDCA/CNEA, 3.0L TDI CASA/CATA

Drive side: RHD

Fitment notes: Right-hand drive hydraulic rack for UK, Australia, South Africa. Extended tie rods for Amarok wide track. Integrated pressure relief valve. Note: RHD internal valve body is mirror-reversed from LHD 2H1422055C.

Before ordering, verify your vehicle's exact model year, engine code, and steering configuration. Some Volkswagen models use different steering racks depending on the market region and optional equipment. Cross-reference the OE numbers listed below with your existing part to ensure compatibility.

OE Number Cross-Reference — VW Amarok 2011- RHD

The following OE (Original Equipment) numbers are cross-referenced for this hydraulic power steering (hps). If your existing rack bears any of these numbers, this replacement unit is a direct fit:

When comparing OE numbers, check the complete number including suffix letters. Volkswagen often uses updated part numbers that supersede older versions — all numbers listed above are interchangeable for this application.

Hydraulic Power Steering System — Technical Details

The VW Amarok 2011- RHD uses a conventional hydraulic power steering system. The rack-and-pinion mechanism converts rotational steering wheel input into linear motion of the tie rods, which turn the wheels. Hydraulic pressure from the engine-driven pump assists this movement, reducing driver effort.

The hydraulic circuit includes the steering rack, high-pressure hoses, return lines, reservoir, and vane pump. The rack contains a rotary valve that directs hydraulic fluid to the appropriate side of the piston based on steering direction. Internal seals prevent fluid bypass and maintain system pressure. A pressure relief valve protects the system from over-pressure conditions.

Installation Guide — VW Amarok 2011- RHD

Installing the hydraulic power steering (hps) on a Volkswagen Amarok (2H) requires careful preparation. Follow these steps for a successful replacement:

1. Vehicle preparation: Raise the vehicle on jack stands and secure the front wheels. Disconnect the negative battery terminal. Place a drain pan under the steering rack to catch hydraulic fluid.
2. Remove wheels and access: Remove both front wheels. On Amarok (2H) models, the inner tie rod ends connect to the steering knuckle via ball joints. Use a tie rod separator tool to disconnect them without damaging the boots.
3. Disconnect steering column: Access the steering column-to-rack coupling from inside the cabin or through the firewall access panel. Remove the pinch bolt and separate the column from the rack input shaft. Mark the relative position before removal.
4. Disconnect hydraulics: Using a line wrench, disconnect the high-pressure and return hoses from the rack. Cap the hose ends to prevent fluid loss and contamination. Note the routing for reinstallation.
5. Remove old rack: Slide the rack out through the wheel well or subframe opening. On Amarok (2H) models, you may need to lower the subframe slightly to create clearance.
6. Prepare new rack: Transfer the inner tie rod ends and boots from the old rack (if reusable) or install new ones. Compare the new rack with the old unit to verify length, mounting points, and connector positions match.
7. Install new rack: Slide the new rack into position and hand-tighten the mounting bolts. Reconnect the steering column coupling and torque the pinch bolt to specification (25 Nm). Reconnect the hydraulic hoses using new O-rings.
8. Reassemble: Reconnect the inner tie rod ends, install the wheels, and lower the vehicle. Fill the power steering reservoir with the recommended fluid (ATF Dexron III or equivalent). Bleed the system by turning the steering lock-to-lock 10-15 times with the engine off, then start the engine and repeat.
9. Final check: Verify steering wheel center position. Check for fluid leaks and test drive at low speed first. A four-wheel alignment is recommended after steering rack replacement.

Common Symptoms of a Failing Hydraulic Power Steering on Volkswagen Amarok (2H)

Recognizing the signs of a worn or failing hydraulic power steering (hps) can prevent further damage and costly repairs. Common symptoms specific to the VW Amarok 2011- RHD include:

• Power steering fluid leak: Fluid pooling under the vehicle near the front wheels or visible wetness around the rack boots indicates internal seal failure. On the Amarok (2H), leaks commonly occur at the high-pressure hose connection point.
• Steering play or wandering: Excessive free play in the steering wheel (more than 2-3cm of movement before the wheels respond) indicates worn inner tie rod ends or rack bushings. On high-mileage Volkswagen models, the rack support bushings may degrade.
• Clunking or knocking: A metallic clunk when turning or going over bumps points to worn inner tie rod ball joints or loose rack mounting bolts. On the VW Amarok 2011- RHD, check the pinch bolt at the steering column coupling first.
• Uneven tire wear: Premature or uneven tire wear on the inner or outer edges indicates alignment issues caused by a worn steering rack. The VW Amarok 2011- RHD should maintain toe alignment within ±0.5° per side.
• Whining or groaning noise: A whining noise when turning, especially at low speed, indicates low power steering fluid, air in the system, or a failing pump. On the Amarok (2H), the vane pump is driven by the serpentine belt — check belt tension and pump condition.

Quality Assurance — KITLAMT Hydraulic Power Steering (HPS) for Volkswagen

Every hydraulic power steering (hps) from KITLAMT undergoes a comprehensive quality control process before reaching our customers:

• Material verification: Rack housing is high-grade aluminum alloy (ADC12 or equivalent) with hardened steel rack gear. All sealing surfaces are precision-machined to Ra 0.4μm or better.
• Pressure testing: Each unit is tested at 1.5× maximum operating pressure (typically 120-150 bar) for 60 seconds with zero leakage acceptable.
• Dimensional inspection: Critical dimensions including rack travel, tie rod thread pitch, mounting bolt spacing, and input shaft spline profile are verified against OE specifications using coordinate measuring machines (CMM).
• Functional testing: Completed racks are bench-tested for steering effort (measured in Nm), return-to-center performance, and internal leakage rates before packaging.
• Packaging: Each unit is sealed in a protective bag, secured in custom foam inserts, and packed in a reinforced carton to prevent transit damage.

Why Choose KITLAMT for Volkswagen Hydraulic Power Steering Parts

KITLAMT has been manufacturing steering systems since 2005, specializing in Volkswagen and other major automotive brands. Our advantages include:

• Factory direct pricing: We manufacture in-house, eliminating middleman costs. Typical savings of 30-50% compared to dealer parts.
• OE-matched quality: Every component is produced to the same specifications as the original equipment, with ISO 9001 and IATF 16949 quality management systems.
• Comprehensive catalog: We stock hydraulic power steering (hps) units for Volkswagen models from the 1990s to the latest production years, covering both LHD and RHD markets.
• Global logistics: FCL and LCL shipping options via sea, air, and express courier. Typical lead time: 3-7 days for stock items.
• Technical support: Our team provides OE cross-reference assistance, installation guidance, and troubleshooting support.

Browse all Volkswagen steering racks | View Amarok (2H) compatible parts | Power steering pump for Volkswagen