Peugeot 405 Valve 分配阀

405 Power Steering Control Valve — OE 4048.A4

This power steering control valve is designed for the 405 (LHD) hydraulic steering system. Matched to OE 4048.A4, it regulates hydraulic fluid flow and direction within the steering rack, controlling power assist delivery. The rotary spool design senses driver input torque and directs pressurized fluid to the correct side of the rack piston. When the valve wears, steering may feel uneven, develop a dead spot on-center, or cause the vehicle to pull. Replacing the valve restores balanced assist without needing a complete rack assembly.

Technical Specifications

SKU: KL-YX8067-1. Rotary spool valve with torsion bar feedback. Flow rating: matched to 405 pump output (6–10 L/min). Pressure regulation: 10–12 MPa. Spool clearance: 5–8 microns. Torsion bar: calibrated for 405 steering feel. Ports: metric threads matching OE hydraulic lines. Seals: nitrile (NBR) O-rings compatible with ATF DEXRON III. Body: hardened steel spool in honed steel sleeve. Self-contained unit that installs inside the rack housing. The spool lands are ground and lapped in matched pairs to maintain the specified clearance — this prevents internal leakage while ensuring the valve responds instantly to driver input. The torsion bar is a precision spring element that determines the on-center feel and assist progression.

Vehicle Compatibility

This steering gear is a direct replacement for OE 4048.A4, fitting these vehicles (LHD):

• Peugeot 405 Valve LHD.

Must match the specific rack model — using a valve from a different generation results in incorrect assist. Verify OE: 4048.A4. Hydraulic systems only — not compatible with EPS or MSG. If you are unsure which valve fits your rack, contact KITLAMT with your vehicle's VIN and we will confirm the correct part number.

Installation Guide

Replacing the 405 control valve: (1) Remove steering rack from vehicle. (2) Drain all hydraulic fluid. (3) Remove end cap or valve housing retaining bolts on input shaft side. (4) Extract valve assembly — note spool and torsion bar orientation. (5) Inspect valve bore for scoring — if damaged, replace the entire rack. (6) Install new valve with correct spool-to-pinion alignment. (7) Reassemble with new O-rings (included). (8) Reinstall rack, fill with recommended fluid. (9) Bleed system by cycling lock-to-lock with engine off. (10) Start engine, verify balanced assist in both directions, check for leaks. This repair requires experience with hydraulic internals — have a qualified steering specialist perform the work if you are not confident.

Common Symptoms of Failure

A worn valve on the 405 produces: Uneven assist — heavier in one direction from spool wear; Dead spot on-center — vague feel from worn center lands; Pulling — asymmetric pressure pushes rack piston one way; Steering surges — intermittent sticking creates assist fluctuations; Whining noise — internal leakage increases pump load. These symptoms can mimic alignment issues or pump failure — a pressure test at the rack ports confirms the valve as the root cause. If the steering wheel pulses or vibrates at highway speed, the valve may have a burr on the spool land that causes it to oscillate — this is a manufacturing defect covered under warranty.

Quality & Warranty

Each 405 control valve is manufactured to exacting standards. Spool and sleeve are matched-ground as a pair (not interchangeable). Torsion bar is heat-treated spring steel. Sealing surfaces superfinished to Ra 0.2 μm. Hydraulic bench-tested measuring assist pressure in both directions — units with >5% left-to-right pressure variation are rejected. KITLAMT 12-month warranty against defects and premature seal failure. Each valve assembly undergoes a 500-cycle endurance test at maximum system pressure before it is approved for shipment. This test simulates thousands of real-world steering inputs and identifies any latent defects in the spool, seals, or torsion bar.

Related Products

Rebuilding the 405 steering system? Common companion parts:

• Complete steering rack assembly — if the rack bar or housing is also worn
• Power steering pump — replace a noisy or weak pump simultaneously
• Power steering hose kit — old hoses shed debris that contaminates the new valve

Shipping & Ordering Information

This 405 steering component (KL-YX8067-1) ships from our warehouse in Guangzhou, China. Standard delivery takes 5–10 business days to most countries via DHL, FedEx, or UPS. Expedited 3-day shipping is available at checkout. All shipments include a tracking number and are securely packaged in a custom-fit foam insert inside a double-wall corrugated box to prevent transit damage. KITLAMT accepts payment via bank transfer (T/T), PayPal, Western Union, and trade assurance orders. For bulk orders of 10+ units, contact our sales team for volume pricing. We also offer OEM/ODM services — if you need a custom part number, private label packaging, or a modified steering ratio, our engineering team can accommodate your requirements with a minimum order quantity of 50 units.

KITLAMT carries complete steering rebuild kits for Peugeot vehicles. Contact us for parts list and bundle pricing.